* This version DON‘t need update firmware

+ Add VVDI PROG USER MUNUAL 4.7.9 version in Doc folder

+ Add MBM29F400TC/BC-PF, MBM29F400TC/BC-PFTR, MBM29F400TC/BC-PFTN, MBM29F200TC/BC-PFTN, MBM29F200TC/BC-PFTR,

MBM29F200TC/BC-PF, MBM29F800TA/BA-PFTR, MBM29F800TA/BA-PFTN, MBM29F800TA/BA-PF options in <1-EEPROM&FLASH>->

+ Add TC1793-CAN options in <2-MCU>->

+ Add R5F64525JFD, R5F64525LFD, R5F64525KFD, R5F6452NJFD, R5F6452NLFD, R5F6452NKFD options in <2-MCU>->

+ Add SPC5607B options in <2-MCU>->

+ Add RATTAN-ZS options in <5-DASHBOARD>-> 

+ Add HYOSOW-S2-COMPUTER options in <8-OTHER>-> 

+ Add HYOSOW-S2-CCM options in <8-OTHER>-> 

+ Add A6L-C7-SUNROOF-MOTOR options in <8-OTHER>->

This function require internet support

Click the “Upgrade” button enter the upgrade interface, show as following picture

Enter update interface, if software show ”communication with server failed”,please close your Anti-virus and computer firewall and retry. If software show “unable to find equipment”, please reconnect device

Tip information show the latest software version and upgrade information

 Device information show the device SN, device firmware version and the latest firmware version

1. Select the firmware version

2. Click “Start Firmware Upgrade” button

3. Don’t close or pull out USB cable before upgrade finished

1. Click “Software Link 1” or “Software Link 2” button, download software from the web

2. Extract the file

Memory:

ATMEL,CATALYST,EXEL,FAIRCHILD,INTEL,MICROCHIP,MITSUBISHI,ST,TOSHIBA,XICOR

MCU:

RENESAS V850,RENESAS H8X,RENESAS R8C,MOTOROLA MC68HC(9)08,MOTOROLA MC68HC(9)12

MOTOROLA MC9S08,MOTOROLA MC9S12,NXP PCF79XX,ST ST10F,INFINEON XC2XXX,ATMEL,ATMEGA XXXX,

INFINEON XC164CS,MICROCHIP PIC18F,

ECU List:

BMW E Series,BMW F Series,BOMBARDIER,CHANGAN,DELPHI,MAGNETI,MARELLI,RENAULT,OTHER

IMMOBILIZER List：

AUDI,BENZ,BMW,BUCIK,CHEVROLET,STEC,CHRYSLER,FIAT,FORD,GREATWALL,INFINITI,LANDROVER,

JAGUAR,NISSAN,OPEL,PORSCHE,RENAULT,SAICMOTOR,VOLKSWAGEN,ZHONGHUA.

DASHBOARD List:

BUICK,CHANGAN,CHERY,CHEVROLET,DONGFENG,FAW,FORD,GEELY,GREATWALL,HAFEI,TOYOTA,

HANTENG,HAIMA,HONDA,JAC,JAGUAR,JINBEI,JMC,LUXGEN,NISSAN,SGMW,VOLOVO,ZHONGHUA,ZOTYE

REMOTE List:

BMW E Series,BMW F Series

 

 

Read EEPROM chips Use method: Follow the image direction when insert the DIP chip (PIN1 as yellow point show as the picture);

SOP chip need soldering on 16Pin adaptor first, then insert the chip follow the image direction

    Function:       Read & Write MC68HC(9)12, V850, H8X, R5C series chips,current version is V2

   Use method: Soldering the line on pin of chip before read & write

   Notes:

     (1) Please check all connection lines,ensure correct and reliable connection

     (2) Please Don’t lengthen CLK and GND-C line, maybe cause read data failed.

        Function:          Read & Write engine ECU

        Use method:   Connect the ECU and R&W

        Notes:               Please check all connection lines, ensure correct and reliable connection

     Function: Read & Write MC9S08, MC9S12 series chips, current version is V1

     Use method: Soldering the line on pin of chip before read & write

     Notes:

       (1) Please check all connection lines,ensure correct and reliable connection.

       (2) Please Don’t lengthen CLK and GND-C line, maybe cause read data failed.

 

did a few tests today and this is what I found out.

It seems that VVDI prog reading speed is dependent on the processor speed of the computer.

CAS3 0L15Y flash read times

Centrino processor @ 1.6ghz Windows XP = 12mins

Core2 Duo processort @ 2.5ghz Windows 7 32 bit = 5 mins

i7 @ 4.4ghz Windows 7 64 bit = 2mins 30 seconds.

Other programmers do not seem to be affected by processor speed at all.

I also would of thought this was a fairly easy question to answer without me doing all the testing

Tested by me: cas 2, cas 3, cas 3+, Cas4 5m48h, volvo cem v40 all ok.

Is a very good tool and for bmw cas4 .

I tested today D80 and a m35080v6, and they work perfect.

Mine erased D160 (BMW F01 dash) with no problem.

Tried to renew bmw e series 868 key. Vvdi programmer claimed operation success but in tango key is now recognized as transponder type A. locked

I did renew 2 keys! Both worked and now are programmed to cars!

Only thing you need to disconnect from PCB is battery while writing the renew file. (Remove the batteries)

Renew BMW series E 868 key – 100% OK z vvdi-prog v4.5.7

FRM3 works perfectly

More EDC17 under ECU section would be great!

Especially BMW EDC16 and EDC17 for ISN purposes.

BMW F series FEM module reading but for that i can only dream about…

BMW BMSX bike ECU would be great…

Renew pcf7946 and 29f family

Renew E series remote with pcf7942 / pcf7944 would be fine

Unlock and download the 9S12G128 secure without erasing it first would be nice .

erasing all 35080s and d80 with soic clip would be super nice too!

I read the CAS3+ MCU with VVDI Prog and that worked perfect.

BMW FRM3 series Exx – READ and WRITE – OK

BMW KEY series Exx – OK

BMW DashBoard 6WB 160DQWT – READ , ERASE , WRITE – OK

2004 Suzuki Jimny:

The first job i did with this kit was actually a 2004 Suzuki Jimny, literally within around 30 – 45 minutes of the parcel being delivered. The software was quick and easy to install (No cd provided, need to download from dealer website and update to latest version).

Anyway, for the Suzuki i used the VVDI-prog with the EEPROM clip adapter to read the immobox 24c01 in-circuit. Then using the VVDI2 immobiliser data tool, i was able to create a dealer key with an Xhorse 4d/4c chip. Write the new dump back to the immobox with VVDI-prog, put it all back together and worked first time thankfully after previous failed attempts with other devices.

 Anyway end goal complete and happy with the new purchase

BMW EWS3:

I did some testing on the bench with a BMW EWS3 using VVDI2 with the CAS adapter cable (Needs external 12Vdc supply). It reads the EWS ok, but can’t write a file back to EWS.

 I will try reading the EWS3+ that is in my car and produce a dealer key for it.

The file change km’ seems to read from dump ok, and will allow you to modify file with new km (untested on car though). If i get some time later on will try read/write with VVDIprog.

1. VVDI Prog device

2. EEPROM Socket

3. EEPROM Adapter

4. MC9S12 Reflash Cable V1

5. MCU Reflash Cable

6. ECU Reflash Cable

7. USB B-Tyte Cable

8. TB28FXXX Adapter (Optional)

9. PCF79XX Adapter (Optional)

10. New M35080/D80 Adapter (Optional)

11. New EWS3 Adapter (Optional)

12. New EEPROM CLIP Adapter (Optional)

13. New EWS4 Adapter (Optional)